Wednesday, November 11, 2026

Pantry Repair - Nov 2026 ($0)

On a recent trip we lost our salt shaker. It was in the sliding pantry, but fell out of the rack...but it was gone. I determined it went into a hole that for reasons I will never know, was left open behind the pantry. 

There was no way to access the hole without removing the pantry or the back of the cupboard below it. 

I removed the pantry and stuck my phone in as far as I could reach and took a picture. 

Salt Shaker and stuff

Not only did I see the salt shaker but some coffee pods and sugar packets. 







I had to remove the back of the lower cupboard to fish the salt shaker out, the smaller stuff required the use of a grabber. 

Grabbing the small stuff

My arm was not long enough, so I used a grabber. 










Why would LTV leave such a hole in the back of the pantry. 

Open area under the pantry

Holes are on both the back and the right side of the pantry enclosure. 









Hardboard covering holes

I fit a piece of hardboard and stapled it in place to prevent any large objects from getting lost in the future. 









I also noticed that the bottom cupboard had no insulation behind it, I could see the fiberglass shell of the RV completely exposed. I insulated this compartment before I closed it up. It is kind of disappointing that LTV didn't insulate it because they thought no one would ever see it. 

Finally, there are 4 screws in the top and 4 in the bottom that hold the pantry in place. They are quite small, if I had larger ones, I would have replaced them, but it is on my list for the future. That pantry carries a lot of weight going down the road. 


Monday, October 26, 2026

Adding The House2Start Gen 2e - October 26 ($116)

When I upgraded the Serenity Falcon with Lithium Batteries in 2024 I had to remove the Trik-L Start Charger I had installed in 2018 since it was not compatible with Lithium batteries. 

Trik-L Start Install

This resulted in the Chassis battery no longer being charged when plugged into house power. 

Since then I have been putting a trickle charger on the chassis battery when I am going to park it for more than a week. 

I finally got around to ordering a Chassis charger, and settled on the House2Start. It was relatively inexpensive and easy to install. 

House2Start Gen 2e

Ordered directly from House2Start









In Bulk Charge Mode


I tucked it in with the DC to DC charger under the seat behind the driver. 

When I installed the DC to DC charger, I installed a isolator switch which requires an active ignition signal before connecting the charger.  Since I had this I was able to connect the House2Start on the chassis hot side and not worry about it causing the DC to DC charger to turn on. 





We no longer need to worry about running down our chassis batteries when the Serenity sits for more than a few days. 

Wednesday, September 2, 2026

Replacing the Propane Regulator - September 1st 2026 ($100 for 2)

For several years we have been having issues running out generator. I replaced the air filters etc, but it would still run at times and other times not. Although the furnace, stove and refrigerator all seemed to work fine, I decided to change out the regulator. 


Old Regulator
It is pretty buried under the RV. 











The new one is a different brand, recommended on most of the RV forums. 

I ordered it from Boatplicity.

ORDER #1133960

 2 - Marshall Excelsior Co. MEGR-298H Excela-Flo Two-Stage Propane Regulator with 90-Degree Vent.

I purchased 2 since the forums say these fail so often, it is smart to carry a spare. That being said, after changing it out, I would hate to have to do it on the road. 

MEGR-298H

New Regulator









After installing the new regulator, the Onan Generator appears to run well. Time will tell. 

Monday, July 13, 2026

Replacing the Kwikee Step ($760) - July 2026

During our 2023 road trip I hit a hump in the road and badly bent our electric door step. I did field repairs that made if functional enough to use the rest of our trip, although it burned up motor control unit. When I got home, I replaced the contorl unit($52).  It worked again, but was still a bit bent. 

During our 2026 road trip I wrecked our Kwikee Step on a log....again. 

Kwikee badly bent


I straightened it using the LTV jack so it could be used, but it was never going to be right again. 






When we got home from our trip, I ordered a new step from etrailer.com.


Invoice for Kwikee Step



It was a plug and play install, pretty easy. 







The new step is much quieter and works great. 

New Step Installled

The new step is so quiet you can hardly hear it.







Sunday, February 15, 2026

Adding DC Outlets - February 2026, three outlets ~ $50 total.

 Monday, February 9th, we awoke to minus 20F temps....not conducive to enjoying the outdoors, so I decided to lite a fire in the barn and work on the Serenity Falcon. 

9Feb2026 04:15AM

It has been one of the coldest winters in years, we have mostly enjoyed the weather and snow...but this is a bit much. 

















Since we upgraded the batteries in the Serenity, we find that we don't plug in much and most of the time are operating on 12V DC power. We have also started bringing with us a 12V compressor refrigerator (cooler) and installed a Starlink Mini in our skylight that can operate from a 12V source. However, the Serenity has only two 12V outlets, in less than convenient locations. To remedy this I installed three, multi-port 12V/USB outlets. 

1) Outside compartment near the RV entry.  This is to power our 12V cooler when we move it outside and what ever else USB device we need to power. It has 3 12V outlets. 1 C port, and 3 USB ports. It is also switchable and has a voltmeter. Everything is switched such that when off it does not use any power. 

Eugizmo, 12V, 200W outlet. 









Under the seat behind the passenger

I powered this and the second outlet from the same power source as my leveler jacks, which is protected by a breaker and the socket is also fused.








2) Behind the passenger seat. I used the same power source but installed it in the seat support behind the passenger seat.  This unit also has a meter and when switched off draws no power. 
Behind the Passenger seat

It is always a bit intimidating to drill holes in fine cabinetry. 








12V socket and 2 USB ports

This is a simpler unit of a single 12V socket and two USB ports. It has a 20A rating (240W).









3) In the corner under the rear bed. I put this one here specifically because this is where the 12V cooler lives when it is inside the RV.  The electric bed goes over the cooler at night but it is accessible during the day. I used the same outlet I put behind the passenger seat but for some reason the meter doesn't work, but I really don't care as long as I can switch if off. 
Under the electric bed


I pulled power from a previous USB install I did years ago to power our phones at night. The socket I stole from is in the rear storage compartment under the bed. Honestly, I don't recall where it got power, but I know it is fused, because I did it.  





These installs will allow us to run devices that are 12V without running our inverters, thus allowing our batteries to last a bit longer. 

We have a large 3000W inverter that runs the house 120V system and a small more efficient 400W inverter in the media cabinet, that I installed when we bought the Serenity, that power the TV and a few USB devices (Like the Firestick, Roku and Chrome dongle). 

We are working towards a early March departure south this year, so I am happy to get these off my list before we launch. 

Update September 2026:
All was good on our 2026 long trip, but during later trips, I found that our 12V DC cooler would sometimes toss out an alarm that it was getting low voltage. I had stole power for the rear plugs from an old USB install I did.  The wire for the USB ports was not sized to run a DC cooler. I rewired this with all 12 AWG wire that pulls power for both the USB ports and the DC cooler from the Macerator power source. This power source is delivered on a 10AWG wire that is fed by a 20A breaker in the panel. 

I also replaced the Macerator switch with a 20A switch since I could see some heating on the old 10A switch that I had put in years ago. The Macerator is rated for 16.5A max, I changed the switch from a momentary to a rocker on/off switch years ago, with a switch I had laying around. I told myself that I would change the switch later, but never did....doh. 

All should be good now.